Mini R53 Manuel d'utilisateur télécharger pdf (Page 1)

Parts and Accessories.

Installation instructions.

John Cooper Works Upgrade Kit

MINI Cooper S (R

53)

MINI Cooper S Convertible (R

52)

The installation instructions apply only to vehicles with John Cooper Works tuning kit

(11 12 0 302 673, 11 12 0 303 287)

Retrofit kit No.: 11 12 0 395 131

Installation time

The installation time of approx. 1.0 hours can vary depending on the condition and equipment of the vehicle.

Important information

These installation instructions are mainly intended for use in the MINI dealership network and by authorised

BMW Service Centres;

The target group of these installation instructions are technical personnel trained on MINI vehicles with

corresponding technical know-how.

All work is to be carried out with the aid of currently valid MINI repair instructions, schematic circuit diagrams,

maintenance manuals and working instructions in rational order with the specified tools (special tools) while

paying particular attention to valid safety regulations.

Important information that must be observed after installing the John Cooper Works Upgrade Kit

and to which the customer's attention should be drawn:

It is recommended to use only 98 RON (octane) fuel or fuel with the highest available octane number.

(95 RON fuel 91 AKI minimum)



The service and maintenance intervals are the same as for the standard production vehicles.

NGK BKR 7 EQUP spark plugs are used and should be fitted at each subsequent service and maintenance

interval.



The air cleaner element with part number 13 72 0 395 826 is installed. It must be used at all

subsequent service and maintenance intervals.



In order to avoid unnecessary additional expenditure/costs, if any problems regarding installation,

assembly or operation are encountered, after spending a little time on attempting to finding the

problem (approx. 0.5 hour), an enquiry, including the vehicle identification number, part number of

the installed retrofit kit and a detailed description of the problem, should be sent without delay to

Technical Support via the Aftersales Assistance Portal (ASAP) .

Do not archive the printout of these Installation Instructions as daily updates are conducted through ASAP!

Refer to ASAP for explanations of the pictographs.

All illustrations show LHD vehicles. Carry out the same procedure analogously on RHD vehicles.

1 2 3 4 5 6 ... 11 12

Résumé du contenu

Page 1 - Installation instructions

Page 2

10© BMW AG, München 01 29 0 397 166 10.20045. Workshop certificateThe workshop certificate is an integral part of the installation instructions (see

Page 3 - Contents

11© BMW AG, München 01 29 0 397 166 10.20046. Finishing off- Reassemble vehicle in reverse order of removal.- Reconnect battery-Perform quick test- P

Page 4 - 1. Parts overview

12© BMW AG, München 01 29 0 397 166 10.2004Workshop certificateThis certificate confirms that the John Cooper Works Upgrade Kit (11 12 0 395 131) has

Page 5 - 2. Preparatory work

2© BMW AG, München 01 29 0 397 166 10.2004Pictographs:identifies information that draws attention to specific requirements. identifies the end of an

Page 6 - 3. Installation

3© BMW AG, München 01 29 0 397 166 10.2004ContentsSection Page1. Parts overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Page 7 - 050 0545 V

4© BMW AG, München 01 29 0 397 166 10.20041. Parts overviewKeyAAir cleaner casingBPartitionCFuel injector nozzleDHeat shieldECrimp connectorABCDE050

Page 8 - 050 0548 V

5© BMW AG, München 01 29 0 397 166 10.20042. Preparatory workTIS No.Perform quick test---Disconnect negative terminal of battery 12 00 ...Remove the

Page 9

6© BMW AG, München 01 29 0 397 166 10.20043. InstallationInstall fuel injector nozzles C as per TIS No. 13 64 541.Undo bolts (1) and remove partitio

Page 10 - 5. Workshop certificate

7© BMW AG, München 01 29 0 397 166 10.20043. InstallationPass black wire (1) from partition wiring harness B with cable lug through grommet (2) and c

Page 11 - 6. Finishing off

8© BMW AG, München 01 29 0 397 166 10.20043. InstallationConnect (by twisting) yellow wire (1) to the one end (2) of the white/red wire.Connect white

Page 12 - Workshop certificate

9© BMW AG, München 01 29 0 397 166 10.20044. Programming and encoding engine control unit ECU (DME or EMS2K)A DISplus or GT1 is necessary to program

Plus de documents pour Électronique des véhicules automobiles Mini R53

Voir le document Mini R53 Manuel d'utilisateur

Mini R53 Manuel d'utilisateur (25 pages)

Commentaires sur ces manuels

Pas de commentaire

Mini R53 Manuel d'utilisateur Page 1

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Électronique des véhicules automobiles Mini R53. The JCW upgrade kit Manuel d'utilisatio

Résumé du contenu

Plus de documents pour Électronique des véhicules automobiles Mini R53

Commentaires sur ces manuels

Mini R53 Manuel d'utilisateur Page 1

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Électronique des véhicules automobiles Mini R53. The JCW upgrade kit Manuel d'utilisatio

Résumé du contenu

Plus de documents pour Électronique des véhicules automobiles Mini R53

Commentaires sur ces manuels

Produits connexes et manuels pour Électronique des véhicules automobiles Mini R53